How to install an electric heated towel rail in the bathroom yourself

A heated towel rail is an element that was most likely present in every Soviet apartment. Today they have changed dramatically and become even more convenient. On it you can hang wet things that need to be dried. Until a certain period, only water structures were operated that were connected to the general water supply. This was very inconvenient, because a rigid attachment to a common riser made it difficult to transfer or replace them. The modern market offers new heated towel rails that can be installed in any convenient place.

Installation of an electric heated towel rail

First of all, you need to decide in which place you will carry out the installation of this design. Before you install an electric appliance yourself, you should carefully consider the location, because ease of use is important, as well as the overall design of the room should not be violated.Most often, the heated towel rail is located near the sinks. Do not forget that the device will need to be connected to power.

IMPORTANT. If the bathroom is not wired and the outlet is not installed, to connect the heated towel rail, it will be necessary to lay the cable in an electrical box.

The cable must be selected with double insulation, and the cross section must be at least 2.5 mm2. Choose a power outlet with splash protection.

REFERENCE. A suitable outlet will be marked on the back of two digits, and the second of them should be 4 or 5.

Mounting to the wall is carried out with three or four screws with the help of plastic dowels and screws. Fasteners should choose galvanized or stainless steel. The editing algorithm is as follows:

1. Attach the structure to the mounting location and mark where you will make the first hole.
2. Drill a hole. Install the dowel and bore the construction screws. Mark the location of the next hole.
3. Also grab the heated towel rail in the second hole and make the remaining holes. Fasten the appliance.

Be careful not to damage the appliance. If possible, install in a protective film on the pipes, and remove it after the structure is securely attached to its place.

Connecting an electric heated towel rail

As already noted, previously, these devices were part of the water supply systems and practically nothing could interfere with their proper operation. The hydraulic resistance in the pipe did not change even as a result of elongation of the line.

Simple wiring diagrams

The most primitive scheme is the one that many have seen in their bathrooms. When the heated towel rail is part of a hot water riser. Thanks to the simplicity and reliability of this type of connection, apartment owners often choose it.

It will be enough to find a modern model of the device, where the necessary interaxal distance and pipe diameter are observed in order to prevent narrowing of the riser.

Recommended Wiring Diagrams

In addition to the standard connection scheme, there are others that also perform well in operation. With their proper implementation, the heated towel rail will cope with the tasks assigned to it.

1. Lateral connection. Masters advise choosing this scheme in most cases.There is no dependence on the pressure of water in the riser and its speed. It does not matter the distance from the riser. If the device is connected correctly, you will not have to bleed air after a temporary shutdown of water.
2. Bottom connection. This method of connection is in demand for the reason that it makes it possible to hide communications, while not having to perform drastic measures. Also, it is worth noting that a lot of models are created specifically for such a connection. This circuit is less efficient than a side or diagonal connection circuit.

Obviously inoperative wiring diagrams

Some masters, in pursuit of an attractive exterior design or due to space saving, choose unreasonable connection schemes for such devices. This may cause the device to not heat up if all systems function properly.

1. It is impossible that there is a hump or arch on the upper section, this will certainly lead to the fact that the airing of the system will occur and the circulation through the heated towel rail will stop.
2. It is not permissible to install the lower outlet at a level below the extreme lowest point of the structure.
3. When organizing a lower eyeliner, the circuit will also be ineffective.

These are the main mistakes that some home masters make out of inexperience. So that you do not encounter them, it is recommended to choose the most common connection schemes for a heated towel rail and not come up with anything new.