The refrigerator door does not close

Broken refrigerator doors are often the reason for acquiring a new product. If there is no tightness over time, the equipment will become unusable. Therefore, it is recommended to carefully monitor the condition of the refrigerator, checking how tightly the door closes. This will help to avoid deterioration of the unit and correct the situation on time.

Tightness - the basis of the normal operation of the refrigerator

In the absence of a tight closing of the door, warm air begins to flow into the refrigerator. At least ice will form on the walls of the equipment. You can get rid of it by defrosting. But such consequences are most harmless. In the worst case, the thermostat will cease to function correctly, which will lead to useless circulation of freon by the cooling system.

The equipment will start to wear, then the motor will overheat and inevitably break. Have to purchase a new unit. To avoid this, it is recommended to take timely measures to correct the situation.

Ways to check the tightness of the refrigerator if the door does not close

If the doors no longer fit snugly against the refrigerator, you should find the reasons for this. First inspect the contents of the unit. Perhaps the leak is broken due to the handle of the pan or the drawer that is not fully pushed in. If everything is okay inside, you should use the following verification methods:

  1. Make sure the unit is installed correctly. A barely noticeable, minimal tilt is allowed. But it is better if the product is perfectly aligned.
  2. Check how tightly the doors are pressed against the equipment box. To do this, you need a paper probe, which helps to verify the tightness.

In some cases, you can repair yourself. But if this is not possible, you should contact a professional. Do not waste time, otherwise the refrigerator will quickly become unusable.

The main reasons why the door may not close

There are several reasons that could provoke a similar situation. Among the most common:

  1. Something is interfering inside. It has already been noted that a pan handle or container that is not fully pushed against the wall can lead to a leak. This reason is one of the most common. Therefore, it is recommended that you start the search for reasons precisely by checking the correct location of the products in the unit.
  2. Rubber compressor. If it is dirty, greasy or worn out due to a long service life, then the door will stop closing tightly.
  3. Broken spacer element. He could be shaken, which led to similar consequences.
  4. The door is deformed. This could be due to regular overloading of it with bottles, heavy products.
  5. Incline. Uneven floors negatively affect the operation of the closing mechanism.

How to independently test the refrigerator door for leaks

This will require a piece of paper. It needs to be fixed on the rubber door seal. Then try closing it. If the door fits snugly on the box and the sheet continues to hang, this indicates the absence of leakage. If this does not happen, the sheet falls, then you need to find the cause of the problem and fix it.

Reference! If you are not confident in your own abilities for troubleshooting, it is recommended to consult a specialist. Otherwise, you can only aggravate the situation.

Self-repair of leakage

There are several different malfunctions associated with tightness and, accordingly, ways to correct the situation. Therefore, you should deal with each.

How to change the seal yourself. (Step-by-step instruction)

The sealant is a special elastic band, which helps to keep the doors tightly closed. In some situations, replacement may be required. To do this, follow the instructions:

  1. Prepare the necessary tools. In addition to the new seal, you will need glue and a flat screwdriver.
  2. Prepare the equipment. Turn off the refrigerator, wait about 30 minutes. Remove the old seal by pulling it with a screwdriver. It is also worth unscrewing the bolts.
  3. Sweep. You will need a sponge and a soap solution. It is necessary to clean the channel for the gum.
  4. Replace. A new rubber band stretches along the entire contour of the door. It is inserted into the channel, fix with glue. The design should be heated with a hairdryer. If there is no special building, the usual one will do.
  5. Check it out. If everything is done correctly, the unit should open with a little effort. If there is no suction effect, then the gum is not tight and should be fixed.

How to adjust the door. (Step-by-step instruction)

To adjust the door, follow the instructions below:

  1. Training. Need a wrench. It is also worth disconnecting the product and leaving it for 30 minutes.
  2. Fit. Open the unit and loosen the bolts slightly from above and below. Then you need to tighten them. If there is a skew from above, then it is recommended to remove one top tab, and the screws are tightened back. If the problems are at the bottom, then it is worth doing the same manipulations, but from below.

Reference! It is recommended not to make the adjustment alone. It is better if someone helps to hold the product so that the unit does not deform.

How to eliminate a skew. (Step-by-step instruction)

To eliminate the skew, it is sometimes necessary to outweigh the door. To do this, follow the instructions below:

  1. Preparatory stage. The equipment is turned off and left for a while. If the design allows, it is worth removing the covers below and above.
  2. Withdrawal. Begin unscrewing the bolts from the ones below. This will require a screwdriver. After the bottom, proceed to the top. Listen carefully to the item.
  3. Outweighing. It is worth performing this action with an assistant. The part is heavy and more convenient if the second person will hold it. Move it to the other side. Then start screwing in the bolts. First top, then bottom. Put the plugs on the existing holes. Return the cover to its original position. Make sure that the work done is correct. If necessary, tighten the bolts more firmly.

How to prevent the refrigerator door open problem

To avoid such problems, it is recommended to follow some tips:

  1. Try not to slam the doors.
  2. Once you have closed the refrigerator, do not immediately open it again.
  3. The sealant needs regular cleaning. Therefore, it is worth monitoring the state of the gum in the unit.

These tips will reduce the risk of poor sealing and complete structural failure.

Watch the video: How to fix and adjust your refrigerator doors that will not close properly (March 2024).

Leave Your Comment